Our Work Videos

What You're Actually Watching: Real Site Footage From Delhi NCR

Every clip in the feed above is genuine, unedited site footage from an actual job completed by Vishwakarma Fabrication Work Pvt. Ltd. — not stock video, not a rendered mockup, and not someone else's work borrowed for marketing. We record these videos during real client visits across Delhi, Noida, Gurugram, Faridabad, and Ghaziabad, specifically so you can see our cutting, welding, fitting, and finishing process before you ever pick up the phone to book a job.

This page exists because photos alone don't show how a gate actually swings once it's hung, how a railing holds up under a hand pressing down on it, or how clean a weld line looks in daylight rather than a studio-lit product shot. Video shows the real thing, warts and all, which is exactly the point.

Our Fabrication Process, Start to Finish

Every project you see in these videos went through the same disciplined process, regardless of size:

1. Site Visit & Measurement

Before any cutting or welding begins, our team visits the site to take accurate measurements and understand the actual space — a gate opening, a balcony edge, a shed span. Guesswork at this stage is what leads to gaps, misalignment, and rework later, so we treat measurement as a job in itself, not a quick formality.

2. Design & Material Selection

Based on the measurements and the client's requirement, we select the right material — mild steel, stainless steel, or a combination with glass or polycarbonate sheeting — and plan the structure's frame gauge and support spacing to match the actual load it needs to carry.

3. Cutting & Frame Fabrication

This is where most of our video footage comes from — the actual cutting, grinding, and frame assembly, either at our workshop or directly on-site depending on the scale of the job. You'll notice in the videos that joints are cleaned and squared before welding, not just tacked together and hoped for the best.

4. Welding

Depending on the material and the job, our welders use MIG, TIG, or Arc welding techniques. What you'll see in the reels is deliberate, controlled welding — steady bead lines, not rushed spot-welds — because a weld that looks clean usually is structurally clean too.

5. Grinding & Surface Finishing

Raw welded joints are ground smooth, edges are deburred, and the surface is prepared for priming and painting. This step rarely gets attention in fabrication marketing, but it's a major factor in how long a gate or railing actually lasts before rust starts creeping in.

6. Priming & Painting

A rust-primed base coat goes on before the final finish, particularly important for anything exposed to Delhi NCR's monsoon humidity. You'll see this stage in several of the videos, especially on gate and railing installations.

7. On-Site Installation

The final structure is transported and installed on-site, with hinges, locks, or mounting hardware fitted and tested. This is often the most visually satisfying part of the video — watching a fabricated piece go from workshop frame to a finished, functioning gate or railing in the actual space it was built for.

8. Final Inspection

Before we consider a job complete, the installed piece is tested — a gate is opened and closed repeatedly, a railing is checked for wobble, a shed roof is checked for proper drainage slope. What doesn't pass this stage gets corrected before we leave, not left for the client to discover later.

Types of Projects You'll Find in the Video Feed

MS & SS Gate Fabrication

Main gates, sliding gates, and pedestrian gates in mild steel and stainless steel, from simple functional designs to more detailed decorative work. Several videos show the full swing/slide test after installation, so you can judge the fit for yourself. Gate fabrication is one of the most common jobs we film, partly because it's the highest-visibility fabrication work most homeowners invest in, and partly because it's genuinely one of the clearest ways to demonstrate fit and finish on camera — a gate that swings freely, closes flush, and latches properly on the first try tells you almost everything you need to know about the quality of the underlying frame work.

Steel & Glass Railings

Balcony and staircase railings combining steel framework with glass or traditional baluster infill, shot both mid-installation and finished, so you can see how the structure is actually anchored to the floor or wall. Railing footage is particularly worth watching closely, because railings are a genuine safety fixture, not just decorative — the anchoring method, bolt spacing, and base plate sizing shown in these videos reflect load-bearing decisions, not aesthetic ones.

Staircase Fabrication

Spiral and straight-run metal staircases, both structural framing and finished installation, for residential and commercial spaces where a concrete staircase isn't practical. These are among our more complex fabrication jobs, requiring precise measurement of rise, run, and headroom before any material is cut, since even small measurement errors compound significantly across a full staircase run — which is exactly why the measurement stage gets extra attention in these particular videos.

Tin Shed & Polycarbonate Roofing

Parking sheds, terrace covers, and factory roofing in GI sheet, colour-coated sheet, and polycarbonate, including the frame welding stage that determines whether a shed survives its first real monsoon or not. You'll notice particular attention paid to slope in this footage — a shed roof welded dead-flat looks fine on installation day but pools water within the first heavy rain, so proper drainage slope is built into the frame from the start, not adjusted after the fact.

Pergolas

Outdoor pergola structures for terraces and gardens, combining structural steel framing with wood or louvre roofing, shown from frame welding through to the finished outdoor structure. Pergola footage often includes more finishing detail than other project types, since these structures are typically installed in visible outdoor living spaces where surface finish and paint quality matter as much as structural soundness.

Structural & Industrial Welding

Larger structural welding jobs for factories and warehouses — support frames, mezzanine structures, and machinery mounting — filmed on active industrial sites across our Delhi NCR service area. This footage tends to show heavier equipment, thicker material sections, and multi-person crews working together, reflecting the different scale and safety considerations of industrial fabrication compared to residential gate or railing work.

Watching a Video vs. Getting a Quote: What Each Actually Tells You

It's worth being clear about what this video feed can and cannot tell you. Watching our work gives you a genuine sense of quality, process, and finish — the things that are hard to fake and easy to judge with your own eyes. What it cannot tell you is the specific cost, timeline, or feasibility of your own project, because those depend entirely on your exact measurements, material choice, site access, and local conditions.

Think of these videos as answering "can this company do quality work?" and a site visit as answering "what will my specific project actually cost and take?" Both matter, and neither substitutes for the other — which is exactly why we offer both: a public video record of our actual work, and a proper on-site assessment before any quote is finalised.

Quality & Safety Standards You'll Notice On Site

Watch closely and you'll notice a few things that are deliberate, not incidental, on every job we film:

• Protective equipment worn by our welders and fabricators, on every site, every job
• Secured, stable work platforms for any elevated welding or installation
• Clean, ground welds rather than raw, unfinished joints left exposed
• Proper measurement and levelling checks before final installation
• A finished, tested product before the crew leaves site — not a "we'll fix it later" approach

None of this is staged for the camera. It's the same process whether or not a video is being recorded — the camera just happens to be there for a portion of our actual jobs, giving you an honest look at how we work.

Where These Videos Are Filmed

Every clip is shot on an actual client site within our active service area. Based in Badarpur, Delhi, our crews regularly work across:

• Delhi: Badarpur, Saket, Kalkaji, Greater Kailash, Vasant Kunj, Okhla, Jasola, Sarita Vihar, Lajpat Nagar, Nehru Place
• Noida & Greater Noida: Noida, Noida Extension, Greater Noida, Greater Noida West
• Gurugram: Gurugram, Sohna Road, DLF Phase 3
• Faridabad: Faridabad, NIT Faridabad, Sector 21 Faridabad
• Ghaziabad: Ghaziabad, Indirapuram, Vaishali

Why We Show Unedited, Real Footage Instead of a Polished Showreel

Most fabrication companies market with finished-product photography — a clean, well-lit shot of a completed gate with none of the actual process shown. That's not dishonest exactly, but it also doesn't tell you anything about how the work gets done, and how the work gets done is exactly what determines whether a gate lasts five years or fifteen.

We chose to show the process itself — sparks flying during a weld, a frame being squared with a measuring tape, a technician grinding down a joint — because it is the most honest way we know to demonstrate the standard of work you'd actually be paying for. If the process looks careful and deliberate in the video, it was careful and deliberate on your job too, because it's the same crew, the same techniques, every time.

Materials You'll See Us Working With

Across these videos, you'll see fabrication work in several different materials, each chosen for a specific reason:

• Mild Steel (MS): the most common material for gates, railings, and general structural fabrication, valued for strength and cost-effectiveness
• Stainless Steel (SS): used where corrosion resistance and a modern finish matter more, particularly for railings and decorative work
• Galvanized Iron (GI) & Colour-Coated Sheets: for shed and roofing work, chosen for weather resistance
• Polycarbonate Sheeting: for pergolas and light-transmitting roof structures
• Toughened Glass: paired with steel framing for modern railing and partition designs

Material selection isn't guesswork — it's matched to the specific job, the load it needs to bear, and how it will be exposed to Delhi NCR's weather over time.

Tools & Equipment You'll See in Use

Watching the videos closely, you'll notice the same core set of equipment across most jobs — not because we're limited in what we use, but because these tools cover the vast majority of fabrication work reliably:

• MIG welding machines — for fast, clean welds on mild steel, used on the majority of gate and railing frame work
• TIG welding machines — for precision work on stainless steel and thinner material where a cleaner, more controlled weld is needed
• Arc welding equipment — for heavier structural work and thicker material sections
• Angle grinders — for cutting, deburring, and finishing weld joints to a smooth surface
• Measuring and levelling tools — spirit levels, tape measures, and squares used throughout, not just at the initial site visit
• Power drills and fastening tools — for mounting hardware, hinges, and fixing structures to walls or floors

Equipment is maintained regularly rather than run until it fails mid-job — a detail that doesn't show up on camera but directly affects whether a weld comes out clean on the first attempt or needs rework.

What Makes Our Process Different From a Typical Local Contractor

Delhi NCR has no shortage of local welders and fabricators. What these videos are meant to demonstrate — beyond just "we do gates and railings" — is a specific approach that differs in a few concrete ways from a typical unregistered day-labour setup:

Measurement Before Material

Many rushed jobs skip proper measurement and adjust on-site with cutting and re-welding — which shows up later as slightly uneven gaps or a gate that doesn't sit quite square. Our videos consistently show a measurement step before any material is cut.

Finishing as a Real Step, Not an Afterthought

Grinding down welds and properly priming before painting is easy to skip when a job is rushed. It's also invisible in a finished-product photo — you genuinely cannot tell from a photo of a painted gate whether the underlying weld was ground smooth or left rough under the paint. Video, especially mid-process footage, is one of the only ways to actually show this step happened.

Testing Before Handover

A gate that swings freely on camera, right after installation, is a gate that was actually tested before the crew left — not one where a problem gets discovered by the client a week later.

Filming Conditions and Site Considerations

These videos are filmed on real, active job sites, not in a controlled studio environment, which means a few things worth being upfront about. Lighting varies — some clips are filmed in bright daylight, others under overcast skies or site lighting, since we don't reschedule a job around ideal filming conditions. Background noise from the site, traffic, or nearby construction is often present, because it's a genuine working environment, not a soundproofed set.

We think this actually makes the footage more useful, not less. A gate installation filmed in the exact kind of narrow Delhi NCR lane it will actually be used in tells you more about real-world fit and finish than a studio shot ever could. If a weld looks clean under harsh midday sun with dust in the air, it's genuinely clean — there's nowhere for a rushed job to hide in that kind of footage.

From Workshop to Site: How Larger Structures Are Handled

For projects too large to fully weld on a residential site — like bigger gates, staircases, or shed frames — much of the fabrication happens at our workshop first, with only final assembly and installation done on-site. You'll notice this split in several videos: workshop footage showing frame construction, followed by a separate clip of the finished piece being installed and tested at the actual client location.

This approach lets us maintain more consistent weld quality (workshop conditions are more controlled than an active residential site) while still doing the final fit and adjustment exactly where the piece will actually be used. For smaller repair or single-gate jobs, the entire process — cutting, welding, and installation — often happens on-site in a single visit, which you'll also see reflected in the shorter, single-location videos.

A Note on Project Scale: Residential to Industrial

The feed intentionally mixes residential and industrial footage, because both are a genuine part of our regular work. A homeowner's balcony railing and a factory's structural support frame require different techniques, different material gauges, and different safety considerations — but the same underlying discipline of measurement, welding quality, and testing applies to both.

If you're specifically looking for evidence of industrial-scale capability rather than residential fabrication, focus on the structural welding and factory shed clips in the feed, which show larger material sections, heavier equipment, and multi-person crews working on a bigger job than a typical home gate installation.

Common Mistakes We See in Poorly Executed Fabrication Work

Part of why we show unedited process footage is that most fabrication failures trace back to shortcuts taken at exactly the stages that don't show up in a finished-product photo. Having repaired plenty of other contractors' rushed work over the years, these are the mistakes we see most often:

Skipping Proper Measurement

A gate or railing built to an eyeballed measurement instead of an accurate one ends up needing on-site adjustment, additional cutting, and re-welding — introducing exactly the kind of rushed joints that fail early. It also frequently results in a visibly uneven gap between the gate and the frame, which is one of the most common complaints we hear from clients who previously used a different fabricator.

Under-Sized Frame Material for the Load

Using a lighter-gauge frame than a structure actually needs saves a small amount on material cost upfront, but shows up later as sagging gates, wobbly railings, or shed roofs that struggle under monsoon rainwater pooling. Frame sizing should be calculated for the actual load and span, not selected purely to minimise material spend.

Skipping Rust-Primer Before Painting

Paint applied directly over bare or poorly cleaned steel looks identical to properly primed work on day one — and completely different eighteen months later, once rust starts bleeding through the paint at every weld joint. This is invisible in any "after" photo taken right after installation, which is exactly why photo-only marketing can hide this shortcut so easily.

Poor Anchoring on Railings

A railing that looks structurally sound but is anchored with undersized bolts or insufficient depth into the floor or wall is a genuine safety risk, not just a durability issue. This is one of the most important things to actually watch for in installation footage — how the base is fixed, not just how the finished railing looks.

Seasonal Considerations: Why Timing Matters for Fabrication Work

You'll notice some of our video footage shows visibly different weather conditions, and that's not incidental — fabrication work in Delhi NCR genuinely needs to account for the season it's being installed in.

Sheds, pergolas, and roofing structures installed or repaired before monsoon hold up far better than ones rushed into place afterward, since proper slope and drainage planning matters more when it actually has to handle heavy rainfall rather than just look finished on a dry day. Gates and railings painted during Delhi's peak summer heat need adequate drying time between coats, which is why some of our painting-stage footage is spread across multiple site visits rather than a single continuous session. Winter fog and reduced daylight hours can affect on-site scheduling for larger jobs, which is factored into project timelines discussed during the initial site visit.

None of this is meant to suggest fabrication work should only happen in ideal weather — it happens year-round, as the videos show — but the process is adjusted deliberately for the season rather than treated identically regardless of conditions.

Why Local Fabrication Knowledge Matters in Delhi NCR

A gate or shed fabricated for Delhi NCR needs to account for conditions this region actually experiences — heavy monsoon rainfall concentrated into a few months, intense summer heat that can exceed 45°C, and dust levels that accelerate wear on unprotected metal surfaces faster than in many other parts of the country. Some of what you see in our videos reflects decisions made specifically for these conditions rather than generic fabrication practice.

Shed and roofing slopes are calculated for genuine monsoon drainage, not a token angle. Paint and primer choices account for extended UV and heat exposure rather than assuming moderate weather year-round. Gate hinge and lock hardware selection considers dust ingress, since fine dust is a real factor in premature mechanical wear in this region in a way it simply isn't in a cooler, cleaner climate. None of this is dramatic or unusual — it's just the kind of practical, regionally-specific knowledge that comes from twenty years of fabrication work concentrated in one geographic area rather than generic, one-size-fits-all installation.

A Growing Video Library

This page is not a fixed portfolio — it grows as we complete and film more projects. If you've watched through the current feed and want to see more of a specific project type, or want to know whether we've filmed work in your specific neighbourhood, the fastest way to find out is to simply ask us directly. We're generally happy to point you toward the most relevant existing footage for your particular project, or discuss what a similar job for your space might involve.

How to Use These Videos Before You Book

If you're considering fabrication work for your own home, office, or facility, we'd suggest watching a few clips relevant to your project type before contacting us:

• Looking at a gate? Watch the swing/slide test at the end of a gate installation video to judge fit and finish.
• Considering a railing? Look closely at how the base is anchored — this is the single biggest factor in railing safety over time.
• Planning a shed or pergola? Pay attention to the frame welding stage, since that's what determines whether the structure holds up to wind and rain load.
• Have a larger industrial job? The structural welding clips show our approach to bigger-scale fabrication, not just residential work.

Once you've seen the kind of work you're after, reach out with photos or measurements of your own space, and we'll schedule a site visit to scope your specific project.

Frequently Asked Questions

Are these videos real, or stock footage?

Every video is genuine, unedited footage from an actual job completed by our own team. None of it is stock video or footage from another company.

Can I request footage of a specific type of project?

Yes, contact us and mention the type of work you're interested in — gate, railing, shed, staircase, or industrial fabrication — and we can point you to the most relevant existing videos or discuss your project directly.

Do you film every project you complete?

Not every job is filmed — some clients prefer privacy, and some sites aren't suited to filming. What you see here is a genuine cross-section of our regular work, not a curated highlight reel of only our best-looking jobs.

Which areas are shown in these videos?

Footage spans our active service area across Delhi, Noida, Gurugram, Faridabad, and Ghaziabad. Specific location details are usually included in each video's caption.

Can I see more videos than what's shown here?

This page is updated with new footage as we complete more filmed projects. Check back periodically, or follow our social channels for additional updates.

Does watching a video give me an accurate price estimate?

Videos are useful for judging quality and style, but pricing depends on your specific measurements, material choice, and site conditions. A free site visit gives an accurate, itemised quote rather than a rough estimate based on someone else's project.

Do you use the same crew shown in the videos for all projects?

Our core fabrication team works across all our projects, maintaining the same process and standard shown in these videos, regardless of which specific technician is assigned to your job.

Can I bring my own design idea, or only choose from what's shown?

These videos show examples of past work, not a fixed catalogue. We regularly build to custom designs, sketches, or reference photos brought by clients.

How long does a typical fabrication project like these take?

This varies widely by project — a residential gate might take 3-5 days from measurement to installation, while larger industrial structural work can take several weeks. Timeline is confirmed during the site visit.

How do I get a quote for a project like the ones shown?

Contact us by phone, WhatsApp, or the service booking form on our website, and we'll schedule a site visit to assess your specific project and provide a transparent quote.

See the Same Standard on Your Own Project

The process you see in these videos — careful measurement, proper welding, clean finishing, and a tested final installation — is the same standard applied to every job we take on, filmed or not. If you have a gate, railing, shed, staircase, or larger fabrication project in mind, explore our full range of services or contact us to book a site visit.